Видео

Why would your ISP have anything control over a Wi-Fi network created by the Thermostat?

Why doesn't, anyone actually show the position the spigot should be in to replace the new actuator head? if it was removed a while prior to the new replacement?

Why don’t anyone answer the questions ? Very unprofessional

Appreciate ,

What about low voltage?

Please update video. Works different now with iOS 17 and Resideo App

That’s showing 4 wire l have 3 wires only coming out of my old Honeywell as what your changing what’s the difference and what new digital thermostat do you recommend???

Really?? So easy??? 😂😂 No way!

This is an old video because the T3 looks nothing like that so this doesn't help me 😞

With the t3r, do you need to disconnect the old wall mounted Honeywell thermostat?

Brilliant. I had issue when in winter I wanst getting heating on downstairs but upstairs was fine. Then engineer came n changed heating 2port zone valve, still no heating downstairs then flushed whole system, still no heating downstairs then changed the thermostat n it's main signal box. Slowly started getting heating everywhere. But now I'm getting heating on when I turn water on and getting water on when I turn heating on. I can't get anyone to sort this. As it was winter I never turned water on as I was getting boiling water with heating. But now its summer when I turn water on I'm getting heating and I just need both water and heating to work independently. Last year thermostat for timer has also been replaced as thot that may b the issue. Some one pls pls help and advice me. Ppl are saying the 2port zone valve replaced is faulty?

By the way: The shown filter is NOT the F76S! This is the HS10S, a combination water supply unit!

Rubbish Video!

Can you help me change it from a p6 to a p4 setting please?

Is that brass or copper the zvalve

I thought this was a video explaining how to use Evohome, I was so wrong, silly me. It explains absolutely nothing.

A B quelle couleur SVP

These are the worst DIY videos I have seen. No sound so you have to keep looking while doing the job - then no stages shown so trying to pause the video takes you back to the start. Grrr

don't buy this shit..all plastic interlockings..once you put it up it's impossible to take it off unless you break it. I guess a screw or two would have been too costly for Honeywell.. that says something about the quality of the product.

hi there, i am trying to replace my old hcw80 wireless thermostat and receiver, with a newer DT90e i think same as in this video. in the old receiver have a 5 wiring which are (Blue wired in N, then the brown wired in the L (2nd) then i have a black wire which wired in to A, then a grey wired into B and then the earth wired into the E, , do i follow the same with the new receiver dt90e ? if so where do i connect the earth as on the new dt90e there is no E (mark) only C s in this video, any advice? thanks

Good enough installation guide, great product BUT what are the values of the parameters to be set (at the end of the video) ?

My partner has just ordered a wired T3 thermostat, before that we had one of the CM honeywell thermostats and it was a wireless, our wireless thermostat is no longer working, so it is easy enough to mount the T3 WIRED honeywell thermostat?

How do you change the battery

Hi. How to set a wider band. If set for 20’c. It reaches 20 then boiler stops but within minutes it’s on again. How to say 19.8’c before it starts the boiler again please ? Stop the hunting. I’m a customer not an installer etc. Thank you

Resided does well! As a manufacturer of home products in the market, education or product training is very important for gaining more market share! When you have the customers in you mind, you customers will have in their mind.

Just got mine on Friday and instructions are poor. I have had to utube to make it clearer. The instructions don’t even say on and off for the time so it’s not clear what P1 and P2 are and so forth. It says I can put heating on for an hour which will be used a lot at this time of year but have got that clear yet.

Clear as mud!

Thanks so much , very helpful. After refitting a new synchron notor the valve is not full closing through the spring pressure so CH is now on a bit when HW on. Was it necessary to slide the manual lever to open when refitting the motor , I think I did that but can’t be sure? What do I need to do re resetting valve to fully close. Happy to remove motor and refit, it’s as if the valve needs to be reset fully open or shut the motor back in. Right now manual lever slack until last 1cm of travel to manually open. Oh and my Synchron motor did not come with new machine screws, the originals are slot head brass and super fiddly to refit, most motors come with cross head machine screws.. what size are they? ( this is an older Honeywell head that cannot be replaced without a drain down) Would be so grateful for help here. Regard Mike

Shocking

Пожалуйста на русском языке

Is this as loud as the Honeywell CM707 when it calls for heat? **CLICK**

It does the job. Excellent product.

6

no sound ?

All I want to do is set the bloody thing to come on in the morning and turn off at night and If I need a temp. boost anytime not needing to be a NASA engineer to be able to do it.

Meanwhile you have yet to add evohome to the total connect comfort app

Chronically bad video

Hi. Is there anyone who could answer some questions please? Please???

What a crap demonstration

Why does my radiators come on night time l have not programmed them and how to cancel them

What are the S1, S & S2 connections for? Can't seem to find that information.

Great video well explained good man

I recently replaced my 3 port valve, seems to work well, but the auto manual arm has no resistance to it, unlike the one i took off, just cannot see any reason why, can you help ? Mike.

website is useless...tells nothing about what items you may need to complete an installation.

What a waste of time the ‘instructions’ are, doesn’t tell you what you need to know. Ended up like a roasted turkey last night, boiler ended up being on all night at 27deg despite the fact I’d spent ages trying to programme the thermostat, obviously I failed. Need clear precise instructions, i.e. MOFR and SASU flashes, nowhere does it say what that means and I still don’t know! Really fed up and disappointed with this. Getting a Hive and having it installed on my mob instead. Final words...ABSOLUTE RUBBISH INSTRUCTIONS!!! Get them rewritten so us not so techy bods can understand!!!

IF SCREEN IS FLASHING WITH ANY NO WHAT IS THE CASE FOR UNIT SETTINGS

A load of damned rubbish! If this is the best Honeywell can do, then they should apply for bankrupcy!

Not really telling you how to work it !

Are the batterys for backup? Also can I confirm this is simply just 2 switching wires no neutral is required

How do i wire the T3R wireless with my combi boiler? i put in the receiver box the wires in A and B and that goes in the combi boiler? and the N and L goes with the power cable? or it doesnt require power cable as it takes the power from the boiler? does someone know???